[ Pobierz całość w formacie PDF ]
.214 Maintenance and careHeadlamps low beamDisconnect the electricalconnector, turn the bulb holdercounterclockwise and replace it.Do not touch the glass part of thebulb and pay attention to the tabguides when replacing.Headlamps high beamReplacement instructions are thesame as for the low beamheadlamp.Headlamp alignmentCheck the headlamp alignmentafter each replacement of a bulb.Refer to Aiming the headlamps inthis chapter.215 Maintenance and careReinstalling the headlampassemblyAll bulb connectors must becorrectly connected.Install in the reverse order.Foglamps (if equipped)1.Open the flap in the lowerradiator grille.2.Remove the screw and pull thefoglamp assembly out.3.Disconnect the electricalconnector.4.Remove the cover from the rearof the foglamp assembly.5.Disconnect the electricalconnectors and release the wireclip from the bulb.6.Install the new bulb in reverseorder (do not touch the glass partof the bulb).216 Maintenance and careSide marker lamps1.Push the complete lightassembly to the front and pull itout.2.Remove the glass from theassembly by turning itcounterclockwise.3.Pull the bulb out and replace it.Brake/turn signal/tail/backuplamps1.From the trunk, remove thecarpet cover from the lampassembly.2.Remove the three retainer nutsand pull the lamp assembly out.3.Turn the bulb counterclockwiseand pull it out.4.Replace the defective bulb.Parking lampsTurn the socket counterclockwiseand pull it out.Pull the bulb outand replace it.217 Maintenance and careLicense plate lampUnscrew the bulb holder with a flatblade screwdriver.Turn the socketcounterclockwise and remove it.Pull the bulb out and replace it.Luggage compartment lampPry out the light assembly from theholder with a flat blade screwdriver.Turn the spherical bulb under slightpressure counterclockwise andremove.High mounted brake lampRemove the push pins and coverfrom the liftgate.To remove thepush pins, press the two tabs of thepush pin insert inward and pull theinsert out.Remove the push pin.Turn the defective bulbcounterclockwise, pull it out andreplace it.218 Maintenance and careInterior lampsSwitch off the interior lamps(middle switch position).Pry outthe lamp assembly with a flatscrewdriver, release the reflector atthe side and replace the festoonbulb.To install, fit the new bulb inreverse sequence.Reading lamps (if equipped)Open the lamp assembly.The bulbs can be replacedafter thecontact plate has been hingedback.Bulb specificationsFunction Trade numberFront /turn lamp 3157 NAHeadlamp (high) 9005Headlamp (low) 9006Foglamp 893Rear tail/turn/brake lamp 1157Backup lamp 1156High mountedbrake lamp 2825/W5WLicense plate lamp 168Side marker lamp 194219 Maintenance and careAIMING THE HEADLAMPSThe alignment of your headlampsshould be checked if:" Oncoming motorists frequentlysignal you to deactivate your highbeams, and your high beams arenot activated." The headlamps do not seem toprovide enough light for clear nightvision." The headlamp beams are pointedsubstantially away from a slightlydown and to the right position.Aiming the headlampsYour vehicle is equipped with aVehicle Headlamp Aim Device(VHAD) oneach headlamp body.Each headlamp may be properlyaimed inthe horizontal direction(left/right) and the verticaldirection (up/down).Turning theheadlamp adjusting screws in thedirectionshownby the embossedarrow markings on each headlampbody represents a change in aimdirectioneither inthe left/right orup/down directions, depending onwhether you are adjusting thehorizontal or the vertical screw,respectively.A non zero bubble reading does notnecessarily indicate out of aimheadlamps.If your vehicle is notpositioned on a level surface, theslope will be included in the levelindicator.Therefore, verticalheadlamp adjustment should beperformed only when beamdirectionappears to be incorrect.220 Maintenance and careCAUTION: THE VERTICAL AIMMUST BE ADJUSTED FIRST.You will need a 6 mm Allen wrenchor a Phillips screwdriver.If the vehicle has been in anaccident, the vehicle's frontstructure should be properlyaligned before aiming theheadlamp.Adjusting the vertical aim1.Park the vehicle on a levelsurface.2.The vertical indicator is locatedon top of the headlamp assembly;the adjusting screw is locatedbehind the headlamp assembly.3.Turn the vertical adjusting screwuntil the bubble aligns with the 0"reference mark when viewed fromdirectly above.The 0" referencemark is the middle of the three (3)bold graduation marks.221 Maintenance and careAdjusting the horizontal aimCAUTION: Do not adjust thehorizontal aim until after adjustingthe vertical aim.1.Parkthe vehicle on a levelsurface.2.The horizontal indicator and theadjusting screw are located behindthe headlamp assembly.3.Turn the horizontal adjustingscrew until the indicator in the vialaligns with the 0" markon theplastic slide located on theindicator housing (vial).When the horizontal and verticalindicators are set to the 0" mark,the headlamp has been properlyaimed.222 Maintenance and careVEHICLE CAREWashing your vehicleOnly use car washing areasthat have environmentallyfriendly drainage systems.Wash your vehicle regularly withcold or lukewarm water.Never usestrong detergents or soap.If yourvehicle is particularly dirty, use aquality car wash detergent.Alwaysuse a clean sponge, washing gloveor similar device and plenty ofwater for best results.To avoidspots, avoid washing when thehood is still warm, immediatelyafter or during exposure to strongsunlight.223 Maintenance and careDuring winter months, it isespecially important to wash thevehicle on a regular basis.Largequantities of dirt and road salt aredifficult to remove, and they alsocause damage to the vehicle.Remove or lower any exterioraccessories before entering a carwash.Remove particles such as birddroppings, tree sap, insect remains,tar spots, road salt and industrialfallout immediately.After washing, apply the brakesseveral times to dry them.Waxing your vehicleThe best way to determine whenthe paintwork needs waxing is bynoting when water stops beadingon the surface.This could be everythree or four months depending onoperating conditions.Use only carnauba orsynthetic based waxes.Removeany bugs and tar before waxing thevehicle.Use cleaning fluid oralcohol with a clean cloth toremove bugs.Use tar remover toremove any tar spots.224 Maintenance and careRepairing paint chipsMinor scratches or paint damagefrom road debris may be repairedwith touch up paint, paint repairfoil or aerosol spray from the Fordaccessories line.Observe theapplication instructions on theproducts
[ Pobierz całość w formacie PDF ]